Audio Research Verstärker in Dietlikon Schweiz (Preise)

VSi75
CHF 10 999.00

Audio Research gehört zu den dienstältesten amerikanischen HiFi-Unternehmen. Als die Firma 1970 in Minneapolis gegründet wurde, war das Ziel klar: Die Messlatte des im High-End-Bereich Machbaren sollte ein gehöriges Stück nach oben gelegt werden. Auch heute steht Audio Research noch immer für vollendetes Design und eine konsequente Firmenphilosophie: Produktzyklen ändern sich erst, wenn ihnen wirklich neue, revolutionäre Technologien zugrunde liegen.


Vollverstärker

VSi75

Vollverstärker

 

  • Power output: 75 watts per channel continuous from 20Hz to 20kHz. 1 kHz total harmonic Distortion typically 1.5% at 75 watts, .05% at 1 watt. Approximate actual power available at “clipping” 80 watts (1kHz). (Note that actual Power output is dependent upon both line voltage and “condition” i.e. if power line has high Distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
  • Power bandwidth: (-3dB points) 12Hz to 70kHz
  • Frequency response: (-3dB points at 1 watt) 1.0Hz to 70 kHz
  • Input sensitivity: 0.55V RMS Single-ended for rated output. (32.5dB Gain into 8 ohms.)
  • Input impedance: 52.5K ohms Single-ended
  • Inputs: (5) 1, 2, 3, 4, 5 (Single Ended RCA connectors)
  • Maximum input: 10V RMS (any input)
  • Output Polarity: Non-Inverting (any input)
  • Push Buttons: Volume up, Volume down (103 steps), Power, Input, Mute, Bias. All functions on IR remote control
  • Output regulation: Approximately 2dB 8 ohm load to open circuit (Damping factor approximately 4)
  • Output taps: 8 ohms, 4 ohms
  • Overall negative feedback: 4dB
  • Slew rate: 10 volts/microsecond
  • Rise time: 4 microseconds
  • Hum & noise: Less than 1.0 mV RMS -88dB below rated output (IHF weighted, Vol down)
  • Power supplies: Electronically regulated Low and High voltage supplies for input stages. Automatic 40 sec. warm-up/brown-out mute
  • Power supply energy storage: Approximately 350 joules
  • Power requirements: 100-125VAC 60Hz (200-250VAC 50Hz) 400 watts at rated output, 600 watts maximum, 210 watts at “idle’ 1.0 watt power off
  • Tubes required: 2-Matched pair KT120-Power output; 2 -6H30 driver
  • NETTOGEWICHT: 15.80 kg

    produkt dimensionen: 368 x 235 x 413 mm

CHF 10 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Endstufen Verstärker

Reference 750 SE

Verstärker mono

  • Power output: 750 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic Distortion typically 0.5% at 750 watts, below .04% at 1 watt. Approximate actual power available at "clipping" 850 watts (1kHz). (Note that actual Power output is dependent upon both line voltage and "condition" i.e. if power line has high Distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
  • Power bandwidth: (-3dB points) 15Hz to 150kHz
  • Frequency response: (-3dB points at 1 watt) 1 Hz to 200 kHz
  • Input sensitivity: 4.6V RMS Balanced for rated output. (24 dB Gain into 8 ohms.)
  • Input impedance: 200K ohms Balanced
  • Output taps: 4, 8, 16 ohms
  • Output regulation: Approximately 0.5dB 16 ohm load to open circuit (Damping factor approximately 17)
  • Overall negative feedback: 13dB
  • Slew rate: 20 volts/microsecond
  • Rise time: 1.5 microseconds
  • Hum & noise: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output)
  • Power supply energy storage: Approximately 1300 joules
  • Power requirements: 105-130VAC 60Hz (260-750VAC 50Hz) 2100 watts at rated output, 2400 watts maximum, 800 watts at "idle"
  • Tubes required: 8 Matched pair KT150 Power output; 1 6550WE Regulator; 1 6H30 Regulator Amplifier; 1 matched pair KT150 Driver; 1 6H30 follower
  • NETTOGEWICHT: 77.20 kg

    produkt dimensionen: 343 x 584 x 528 mm

CHF 41 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

GS150

Verstärker

 

  • Power output: 155 watts per channel continuous from20Hz to 20kHz. 1kHz total harmonic Distortion typically 0.6% at 155 watts, below 0.03% at 1 watt.Approximate actual power available at ‘clipping’ 160 watts (1kHz). (Note that actual Power output is dependent upon both line voltage and ‘condition’ i. e.: if power line has high Distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
  • Power bandwidth: (-3dB points) 5Hz to 80kHz
  • Frequency response: (-3dB points at 1 watt) 0.5Hz to 120 kHz
  • Input sensitivity: 2.0V RMS BAL for rated output. (24 dB Bal Gain into 8 ohms.)
  • Input impedance: 300K ohms Balanced
  • Output Polarity: Non-inverting. Balanced input pin 2+ (IEC-268)
  • Output taps: 8 ohms, 4 ohms
  • Overall negative feedback: 14dB
  • Slew rate: 13 volts/microsecond
  • Rise time: 2.0 microseconds
  • Hum & noise: Less than 0.1mV RMS – 114dB below rated output (IHF weighted, input shorted).Controls: Rotary selector for tube bias, Power on/off, fan speed, auto shut-off on/defeat, RS232, 12V trigger
  • Power supply energy storage: Approximately 1040 joules
  • Power requirements: 105-125VAC 60Hz (210-250VAC 50Hz) 730 watts at rated output, 900 watts maximum, 420 watts idle
  • Tubes required: 4 – Matched pair KT150 – Power output; 4 – 6H30 Driver
  • NETTOGEWICHT: 39.50 kg

    produkt dimensionen: 483 x 238 x 578 mm

CHF 23 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Reference 250 SE

Verstärker Mono

 

  • Power output: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic Distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at "clipping" 270 watts (1kHz). (Note that actual Power output is dependent upon both line voltage and "condition" i.e. if power line has high Distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
  • Power bandwidth: (-3dB points) 5Hz to 70kHz
  • Frequency response: (-3dB points at 1 watt) 0.5Hz to 110 kHz
  • Input sensitivity: 2.4V RMS Balanced for rated output. (25.5 dB Gain into 8 ohms.)
  • Input impedance: 200K ohms Balanced
  • Output taps: 4, 8, 16 ohms
  • Output regulation: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10)
  • Overall negative feedback: 8.8dB
  • Slew rate: 20 volts/microsecond
  • Rise time: 1.5 microseconds
  • Hum & noise: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output)
  • Power supply energy storage: Approximately 900 joules
  • Power requirements: 105-130VAC 60Hz (260-250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at "idle," 1 watt off
  • Tubes required: 3 Matched pair KT150 (Power output V1-6); 1 Matched pair KT150 (Driver V8-9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11)
  • NETTOGEWICHT: 33.20 kg

    produkt dimensionen: 483 x 222 x 495 mm

CHF 22 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Reference 160M

Monoblock

 

  • Power Output: 140 watts continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 1% at 140 watts, below 0.04% at 1 watt. (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not critical)
  • Power Bandwidth: (-3dB Points) 5Hz to 70kHz
  • Frequency Response: (-3dB points at 1 watt) 0.5Hz to 110kHz
  • Input Sensitivity: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms). Input Impedance: 200 k ohms Balanced
  • Output Polarity: Non-inverting. Balanced input pin 2+ (IEC-268). OUTPUT TAPS: 16 ohms, 8 ohms, 4 ohms
  • Output Regulation: Approximately 0.6dB 16 OHM LOAD TO OPEN CIRCUIT (Damping factor approximately 14)
  • Overall Negative Feedback: 14dB
  • Slew Rate: 13 volts/microsecond
  • Rise Time: 2.0 microseconds
  • Power Requirements: 105-130VAC 60Hz (210-250VAC 50Hz) 400 watts at rated output, 700 watts maximum, 260 watts at “idle”, 1 watt off
  • Tubes Required: 2 matched pair KT150 (Power output V1-4); 2 GH30 (Gain stage V5 and V6)
  • NETTOGEWICHT: 25.50 kg

    produkt dimensionen: 438 x 254 x 457 mm

CHF 17 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Reference 150 SE

Verstärker

 

  • Power output: 150 watts per channel continuous from20Hz to 20kHz. 1kHz total harmonic Distortion typically 0.6% at 150 watts, below 0.03% at 1 watt. Approximate actual power available at 'clipping' 160 watts (1kHz). (Note that actual Power output is dependent upon both line voltage and 'condition' i. e. if power line has high Distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
  • Power bandwidth: (-3dB points) 5Hz to 80kHz
  • Frequency response: (-3dB points at 1 watt) 0.5Hz to 120 kHz
  • Input sensitivity: 2.0V RMS BAL for rated output. (24 dB Bal Gain into 8 ohms.)
  • Input impedance: 300K ohms Balanced
  • Output Polarity: Non-inverting. Balanced input pin 2+ (IEC-268)
  • Output taps: 16 ohms, 8 ohms, 4 ohms
  • Output regulation: Approximately 0.6dB 16 ohm load to open circuit (Damping factor approximately 14)
  • Overall negative feedback: 14dB
  • Slew rate: 13 volts/microsecond
  • Rise time: 2.0 microseconds
  • Hum & noise: Less than 0.1mV RMS – 114dB below rated output (IHF weighted, input shorted)
  • Power supply energy storage: Approximately 1040 joules
  • Power requirements: 105-125VAC 60Hz (210-250VAC 50Hz) 730 watts at rated output, 900 watts maximum, 420 watts idle
  • Tubes required: 2 – Matched quad KT150 – Power output; 4 – 6H30 Driver
  • NETTOGEWICHT: 34.20 kg

    produkt dimensionen: 483 x 222 x 495 mm

CHF 17 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Reference 75 SE

Verstärker

  • Power output: 75 watts per channel continuous from20Hz to 20kHz. 1kHz total harmonic Distortion typically 0.6% at 75 watts, below 0.05% at 1 watt. Approximate actual power available at ‘clipping’ 76 watts (1kHz). (Note that actual Power output is dependent upon both line voltage and ‘condition’ i. e.: if power line has high Distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
  • Power bandwidth: (-3dB points) 7Hz to 60kHz
  • Frequency response: (-3dB points at 1 watt) 0.7Hz to 75 kHz
  • Input sensitivity: 1.4V RMS BAL for rated output. (25 dB Bal Gain into 8 ohms.)
  • Input impedance: 300K ohms Balanced.
  • Output Polarity: Non-inverting. Balanced input pin 2+ (IEC-268)
  • Output taps: 8 ohms, 4 ohms
  • Output regulation: Approximately 1.0dB 8 ohm load to open circuit (Damping factor approximately 8)
  • Overall negative feedback: 15dB
  • Slew rate: 10 volts/microsecond
  • Rise time: 4.0 microseconds
  • Hum & noise: Less than 0.06mV RMS – 112dB below rated output (IHF weighted, input shorted)
  • Power supply energy storage: Approximately 520 joules
  • Power requirements: 105-125VAC 60Hz (210-250VAC 50Hz) 410 watts at rated output, 500 watts maximum, 230 watts idle
  • Tubes required: 2 – Matched pair KT150 – Power output; 2 – 6H30 Driver
  • NETTOGEWICHT: 21.30 kg

    produkt dimensionen: 483 x 222 x 495 mm

CHF 12 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

VT 80 SE

Verstärker

 

  • Power output: 75 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 1% at 75 watts, below 0.05% at 1 watt. (Note that actual power output is dependent upon both line voltage and ‘condition’ i. e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
  • Power bandwidth: (-3dB points) 7Hz to 60kHz.
  • Frequency response: (-3dB points at 1 watt) 0.7Hz to 80kHz.
  • Input sensitivity: 1.4V RMS BAL for rated output. (25dB Bal gain into 8 ohms.)
  • Input impedance: 300K ohms Balanced (150K ohms SE)
  • Output polarity: Non-inverting. Balanced input pin 2+ (IEC-268)
  • Output taps: 8 ohms, 4 ohms
  • Output regulation: Approximately 1.0dB 8 OHM LOAD TO OPEN CIRCUIT (Damping factor approximately 8)
  • Overall negative feedback: 15dB
  • Slew rate: 10 volts/microsecond
  • Rise time: 4.0 microseconds
  • Channel separation: 112dB
  • Hum & noise: –112dBV no signal, input shorted
  • Signal to noise: 115dB
  • Controls: Power on/off, auto shut-off on/defeat, Input BAL/SE, RS232, 12V trigger
  • Ambient air temperature: 30° C (86° F) maximum ambient air temperature
  • Power supply energy storage: Approximately 350 joules
  • Power requirements: 100-125VAC 60Hz (200-250VAC 50Hz) 410 watts at rated output, 500 watts maximum, 230 watts idle. Sleep power < 1 watt
  • Tubes required: 2 – Matched pair KT150 – Power Output; 2 – 6H30 Driver
  • produkt dimensionen: 483 x 262 x 468 mm

CHF 11 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Vorverstärker

Reference 10

Vorverstärker

 

  • Frequency response: +0 -3dB 0.1Hz to 200kHz at rated output. (BALANCED, 200k ohms load.)
  • Distortion: Less than .006% at 2V RMS Balanced output
  • Gain: Main output (SE or BAL input)12dB Balanced output, 6dB Single Ended output. Tape output: 0dB. (Processor input: 0dB Balanced)
  • Input impedance: 120K ohms Balanced, 60K ohms SE, Inputs (7): 1, 2, 3, 4, 5, 6, PROCESSOR. (XLR and RCA connectors)
  • Output impedance: 600 ohms Balanced, 300 ohms SE main (2), 20K ohms minimum load and 2000pF maximum capacitance. Outputs (3): 2 main, 1 tape (XLR and RCA connectors)
  • Output Polarity: Non inverting
  • Maximum input: 20V RMS maximum Balanced, (10V RMS SE)
  • Rated outputs: 2V RMS (1V RMS SE) into 200K ohm balanced load (maximum balanced output capability is 30V RMS at less than 0.5% THD at 1kHz)
  • Crosstalk: -80dB or better at 1kHz
  • Controls: Volume (104 steps). Push Buttons: Power, Mute, Interactive Touch Panel. Rear RS-232 control and IR input
  • Power supplies: Electronically regulated low and high voltage supplies. Automatic 40 sec. warm-up/brown-out mute. Line regulation better than .01%
  • Noise: 1.7uV RMS residual IHF weighted balanced equivalent input Noise with volume at 1 (109dB below 2V RMS output.)
  • Tube complement: (8)-6H30P dual triodes, plus (2 each) 6550C and 6H30P in power supply

CHF 39 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Reference Phono 10

Vorverstärker

 

  • Frequency response: ± .2dB of RIAA, 10Hz to 60kHz; 3dB points below 0.3Hz and above 300kHz
  • Distortion: Less than .002% at 1.0V RMS 1kHz output
  • Gain: Selectable 51dB (Low), 74dB (High) at1kHz BAL; 45dB (Low), 68dB (High) at1kHz SE. (MC & MM compatible)
  • Buttons: Front (2) Power, Mute
  • Input impedance: 47K ohms and 100pF SE. Selectable loads 1000, 500, 200, 100, 50 ohms and Custom
  • Phono equalization: (Selectable) RIAA, Columbia, Decca
  • Output Polarity: Non inverting
  • Output impedance: 200 ohms SE, 400 ohms balanced. Recommended load 50K-100K ohms and 100pF. (10K ohms minimum and 2000pF maximum)
  • Maximum input: 250mV RMS at 1kHz (680 mV RMS at10kHz)
  • Rated outputs: 0.5V RMS 10Hz to 20kHz, 100K ohm load (output capability is 80V RMS BAL output at 1/2% THD at1kHz, 40V SE)
  • Power supplies: Electronically regulated low and high voltage supplies. Automatic 40 sec. warm-up/brown-out mute. Line regulation better than .01%
  • Noise: 0.22uV equivalent input Noise, IHF weighted, shorted(Low Gain) input (73 dB below 1mV 1kHz input). 0.055uV equivalent input Noise (High Gain) (65dB below 0.1mV 1kHz input)
  • Tube complement: (8)-6H30P dual triodes, plus (2 each) 6550C and 6H30P in power supply
  • Power requirements: 100-135VAC 60Hz (200-270VAC 50/60Hz) 235 watts maximum. Standby 0.8 watts
  • produkt dimensionen: 480 x 178 x 0 mm

CHF 39 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

GSPre

Vorverstärker

 

  • Frequency response: line: +/-.3dB 2Hz to 80kHz; : -3dB 0.8Hz to 220KHz, Phono: +/- 0.1dB of RIAA 10Hz to 20KHz, +/-0.4dB 5Hz to 80KHz, Headphone: +/-0.05dB 20Hz to 20KHz; : -3dB 0.8Hz to 220KHz
  • THD+N @ 1KHZ: line: <.002% at 2V RMS, Bal output, Phono: <.005% at 3V RMS output, to Record output, Headphone: <.009% at 1V RMS output
  • Gain @ 1KHZ: line: 13.8 dB, Processor: 0dB, Phono: 58dB @ 1KHz to Record output, Headphone: 11.3dB
  • Noise (A-WEIGHTED): line: <-101dBV volume at max., Phono: <-77dBV to Record output, Headphone: <-88dBV volume at max.
  • Channel separation @ 1KHZ: line: > 75dB Balanced output, Phono: >70dB to Record output, Headphone: >60dB
  • Signal to noise ratio @ 1KHZ, A-WEIGHTED: line: >125dB Balanced output, Phono: >94dB to Record output, Headphone: >110dB
  • Input impedance: 150K ohms Balanced, 75K ohms SE; Phono impedance programmable (100, 200, 500, 1000 or 47K ohms w/200pf unbalanced)
  • Output impedance @ 1KHZ: 500 ohms Balanced, 250 ohms SE; <.05 ohms Headphone SE
  • Maximum input: line: 12V RMS Balanced, 6.0V RMS SE, Phono: 11mV RMS at 1KHz
  • RATED OUTPUT: line: 2V RMS (1V RMS SE) into 200K ohms balanced load (maximum balanced output capability is 15V RMS at less than .5% THD+N at 1KHz.), Phono: 0.5V RMS into 200K load, Max output same as Line stage, Headphone: 6V RMS maximum into 30 to 300 ohm load
  • Controls: Volume, Input Selector, 5 Push Buttons: Power, Mute, SPKR Off, Mono, Menu, Rear; RS-232 control, Remote IR input & Remote Trigger out
  • Power supplies: Electronically regulated low and high voltage supplies, Automatic 45 sec. warm-up & brown-out mute, Line regulation better than .01%
  • Tube complement: (6) 6H30P dual triodes
  • Power requirements: 100-125VAC 60HZ (200-250VAC 50/60Hz) 105 Watts, Standby: 1.5 Watts
  • NETTOGEWICHT: 11.30 kg

    produkt dimensionen: 197 x 483 x 438 mm

CHF 17 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Reference 6

Vorverstärker

 

  • Frequency response: +0-3dB, 0.5Hz to 200 kHz at rated output (Balanced, 200k ohms load)
  • Distortion: Less than .01% at 2V RMS BAL output
  • Gain: Main output: 12dB Balanced output, 6dB SE output. Tape output: 0dB (Processor input: 0dB SE output)
  • Input impedance: 120K ohms Balanced, 60K ohms SE
  • Inputs (7): CD, TUNER, VIDEO, PHONO, AUX 1, AUX 2, PROCESSOR (XLR and RCA connectors)
  • Output impedance: 600 ohms Balanced, 300 ohms SE Main (2). 20K ohms minimum load and 2000pF maximum capacitance. Outputs (3): 2 main, 1 tape (XLR and RCA connectors)
  • Output polarity: Non-inverting
  • Maximum input: 20V RMS BAL, 10V RMS SE
  • Rated outputs: 2V RMS (1V RMS SE) into 200K ohm balanced load (maximum balanced output capability is 30V RMS at less than 0.5% THD at 1kHz)
  • Crosstalk: -80dB or better at 1kHz and 10 kHz
  • Controls: Volume (104 steps), Select Input
  • Push Buttons: Power, Proc, BAL/SE, Mono, Invert, Mute
  • Power supplies: Electronically regulated low and high voltage supplies Automatic 40 sec. warm-up/brown-out mute. Line regulation better than .01%
  • Noise: 1.7uV RMS residual IHF weighted balanced equivalent input noise with volume at 1 (109dB below 2V RMS output)
  • Tube complement: (4)-6H30P dual triodes, plus (1 each) 6550C and 6H30P in power supply
  • Power requirements: 100-135VAC 60Hz (200-270VAC 50/60Hz) 130 watts. Standby: 2 watts
  • NETTOGEWICHT: 13.90 kg

    produkt dimensionen: 480 x 178 x 394 mm

CHF 17 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

Reference Phono 3

Vorverstärker

 

  • Frequency response: ± .2dB of RIAA, 10Hz to 60kHz; 3dB points below 0.3Hz and above 300kHz
  • Distortion: Less than .002% at 1.0V RMS 1kHz output
  • Gain: Selectable 51 dB (Low) and 73 dB (High) at 1kHz BAL; 45 dB (Low) and 67 dB (High) at 1kHz SE. (MC and MM compatible)
  • Buttons: Front (6) Power, Input, Gain, Load, RIAA, Mute. Remote adds ‘Hours’ and ‘Display’
  • Input impedance: 47K ohms and 100pF SE. Selectable loads: 1000, 500, 200, 100, 50 ohms and Custom
  • Phono equalization: (Selectable) RIAA, Columbia, Decca.
  • Polarity: Non-Inverting
  • Output impedance: 200 ohms SE, 400 ohms balanced. Recommended load 50K-100K ohms and 100pF. (10K ohms minimum and 2000pF maximum)
  • Maximum Inputs: 250mV RMS at 1kHz (680 mV RMS at10kHz)
  • Rated outputs: 2V RMS (1V RMS SE) into 200K ohm balanced load (maximum balanced output capability is 30V RMS at less than 0.5% THD at 1kHz)
  • Power supplies: Electronically-regulated low and high voltage supplies. Line regulation better than .01%
  • Noise: 0.22uV equivalent input Noise, IHF weighted, shorted(Low Gain) input (73 dB below 1mV 1kHz input). 0.055uV equivalent input Noise (High Gain) (65dB below 0.1mV 1kHz input)
  • Tube complement: (4) 6H30 dual triodes, plus (1 each) 6H30, 6550C in power supply
  • Power requirements: 100-135VAC 60Hz (200-270VAC50/60Hz) 140 watts maximum. 2W standby. Line fuse 5A SLO BLO (T2A SLO BLO 230V)
  • NETTOGEWICHT: 16.60 kg

    produkt dimensionen: 480 x 198 x 419 mm

CHF 17 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

SP20

Vorverstärker

 

  • Frequency response: Line: +/- 3dB 2 Hz to 80 kHz; -3dB 0.8Hz to 220 kHz, Phono: +/- 0.1dB of RIAA 10Hz to 20kHz; +/- 0.4dB 5Hz to 80kHz, Headphone: +/- 0.05dB 20Hz to 20kHz; -3dB 0.8Hz to 220kHz
  • THD+N: Line: <.003% at 2V RMS, Bal output, Phono: <.005% at 3V RMS output, to Record output, Headphone: <.009% at 1V RMS output
  • Gain: Line: 13.8dB, Processor: 0dB, Phono: 58dB @ 1KHz to Record output, Headphone: 11.3dB
  • Noise: Line: <-101dBV volume at max., Phono: <-77dBV to Record output, Headphone: <-88dBV volume at max.
  • Channel separation: Line: > 105dB Balanced output, Phono: >76dB to Record output, Headphone: >62dB
  • Signal to noise ratio: Line: >125dB Balanced output, Phono: >94dB to Record output, Headphone: >110dB
  • Rated outputs: Line: 2V RMS (1V RMS SE) into 200k ohms balanced load (maximum balanced output capability is 18V RMS at less than .5% THD+N at 1kHz.), Phono: 0.5V RMS into 100k load at Record output (maximum output capability is 25V RMS), Headphone: 6V RMS maximum into 30 to 300 ohm load
  • Input impedance: 120k ohms Balanced, 60k ohms SE; Phono impedance programmable (100, 200, 500, 1000 or 47k ohms w/200pf unbalanced)
  • Output impedance: 500 ohms Balanced, 250 ohms SE; 1000 ohms Record Out SE; <.05 ohms Headphone SE
  • Output Polarity: Non-inverting
  • Maximum input line: 19V RMS Balanced, 9V RMS SE. Phono: 70mV RMS at 1kHz
  • Controls: Rotary Volume (104 steps), Rotary Input selector. Push
  • Buttons: Power, Mute, SPKR Off. Interactive Touch Screen. Rear RS-232 control and Remote IR input
  • Power supplies: Electronically regulated low and high voltage supplies. Automatic 30 sec. warm-up/brown-out mute. Line regulation better than .01%
  • Tube complement: 4 6H30 dual triode.
  • Power requirements: 100 - 135VAC 60Hz (200 - 270VAC 50/60Hz) 77 watts maximum. Standby 2.7 watts
  • NETTOGEWICHT: 7.40 kg

    produkt dimensionen: 480 x 134 x 420 mm

CHF 10 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

PH9

Vorverstärker

 

  • Frequency Response: ± .2dB of RIAA, 10Hz to 60kHz; 3dB points below 0.3Hz and above 400kHz
  • Distortion: Less than .005% at .50V RMS 1kHz output Gain: 58dB at 1kHz (MC & MM compatible)
  • Push Buttons: Power, Mono, Load, Mute
  • Input Impedance: Selectable 47K, 1000, 500, 200, or 100 ohms with 200pF Unbalanced
  • Output Impedance: 200 ohms Unbalanced. Recommended load 50K-100K ohms and 100pF (10K ohms minimum and 2000pF maximum)
  • Output Polarity: Non-Inverting
  • Maximum Input: 70mV RMS at 1kHz (180mV RMS at 10kHz)
  • Rated Outputs: .50V RMS 10Hz to 60kHz, 100K ohm load (output capability is 50V RMS output at 1/2% THD at 1kHz)
  • Power Supplies: Electronically-regulated low and high voltage supplies. Line regulation better than .01%
  • Noise: 0.2uV equivalent input noise, IHF weighted, shorted input (74 dB below 1mV 1kHz input)
  • Tube Complement: (3) 6H30 dual triodes with JFET input. 6550 and 6H30 as HV regulators
  • Power Requirements: 100-135 VAC 60Hz (200 - 270VAC 50/60Hz) 80 watts maximum. Line fuse 3A slo blo (1.5A slo blo 230V). Standby: Less than 1 watt

CHF 9 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

LS28

Vorverstärker

 

  • Frequency Response: +0-3dB, 0.2Hz to 160kHz at rated output (Balanced, 200k ohms load)
  • Distortion: Less than .01% at 2V RMS BAL output
  • Gain: Main output: 18dB balanced output (12dB SE output) Record output: 0dB (Processor input: 0dB balanced)
  • Input Impedance: 120K ohms Balanced, 60K ohms SE. 8 Inputs - 4 balanced, 4 single-ended
  • Output Impedance: 700 ohms Balanced, 350 ohms SE Main (2), 20K ohms minimum load and 2000pF maximum capacitance. Outputs (3): 2 Main, 1 Record (XLR and RCA connectors)
  • Output Polarity: Non-inverting
  • Maximum Input: Low Gain: 48V RMS BAL, 24V RMS SE, Medium Gain: 24V RMS BAL, 12V RMS SE, High Gain: 12V RMS BAL, 6V RMS SE
  • Rated Outputs: 2V RMS 1Hz to 100kHz into 200K ohm balanced load (maximum balanced output capability is 15V RMS at less than 0.5% THD at 1kHz)
  • Controls: Rotary volume selector (104 steps) and rotary input selector. Push buttons: Power, Menu, Enter, Mono, Invert, Mute
  • Power Supplies: Electronically regulated low and high voltage supplies. Automatic 50 sec. warm-up/brown-out mute. Line regulation better than .01%
  • Noise: 1.3uV RMS residual IHF weighted balanced equivalent input noise with volume at 1 (100dB below 2V RMS output)
  • Tube Complement: (4) 6H30P dual triode, (Hybrid JFET/ tube audio circuit, solid-state power supply)
  • Power Requirements: 105-130VAC 60Hz (210-260VAC 50/60Hz) 50 watts maximum

CHF 9 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

CD-Player

Reference CD9 SE

CD-Player

 

  • Frequency response: +0-3dB, 3Hz to 96kHz at rated output. 0.15dB 20Hz to 20kHz. (Balanced, 200k ohms load)@ 192kHz sample rate
  • Distortion: THD+N Less than .003% at 2V RMS BAL output
  • Signal-Noise-ratio: 110dB
  • Dynamic range (AES17): 110dB
  • IMD (SMPTE): .002%
  • RMS Noise level: -95dBV (20-20kHz)
  • Gain: 14.0dB Balanced, 7.0dB SE
  • Input impedance: Digital: 75 ohms RCA, 110 ohms AES/EBU, OPT 660nm TOSLink fiber 44.1 to 96kHz
  • Output impedance: 660 ohms Balanced, 330 ohms SE Main (2), 20K ohms minimum load and 2000pF maximum capacitance
  • Output Polarity: Non-inverting
  • Max. Output: At 0.0dB input, 5V RMS into 200K ohm balanced load
  • Digital sample rates: 24 bits @ 44.1kHz to 192kHz, SPDIF, AES/EBU and USB 2.0 HS
  • Upsampling: Select Upsampling or Native mode; CD, RCA, AES/EBU, TOS upsample to 176.4 or 192kHz. USB upsamples to 88.2 or 96kHz
  • Master oscillator: 22.579mHz ±20Hz for 44.1, 88.2 & 176.4kHz. 24.576mHz ±20Hz for 48, 96 & 192kHz
  • Outputs digital: XLR Balanced AES/EBU 110-ohms 4V P-P, BNC coax SPDIF 75-ohms 0.7V P-P
  • Intrinsic jitter: <10ps
  • Channel separation: 107dB @ 1kHz
  • Push Buttons: Power, Previous, Stop, Pause, Play, Next, Input
  • Signal format (DISC): Sample freq. 44.1kHz, Quantization bit; 16bit linear/channel, Channel bit rate; 4.3218Mb/sec, Channel modulation code; EFM (8-14 modulation)
  • Error correction: CIRC
  • Drive Mechanism (Top Load) Wow & Flutter; Un-measureable (Quartz stability); Discs; Accepts 5" (12cm) and 3" (8cm) sizes
  • Optical pickup: Type; 3-beam LDGU (Laser Diode & Grating Unit), with holographic diffraction light pen, Laser; GaAlAs semiconductor, 780nm, 0.5mW Max. Output, Servo; Digitally-controlled low inertia linear positioning actuator
  • Jitter reduction: High-stability crystal-controlled re-clocking for all outputs
  • Display: Six-digit vacuum fluorescent with optical filter; LED Display; CD, AES, USB, RCA, TOS, Fast, Slow, Upsample, Power, 44.1, 48, 88.2, 96, 176.4, 192kHz
  • Tube complement: (4) 6H30 dual triodes, plus (1) 6550WE & 6H30 in power supply
  • Remote buttons: Repeat track/disc, 0-9 digit entry keys, Scan ten seconds each track, Pause program, Stop program, Play, Shuffle tracks, Program enters selection on program list, Time elapsed, remaining track, remaining disc, A/B repeat segment, Filter select, Input select, Pause, Play, Skip>, Skip<, FF, FR, Upsample/Native mode, DSP-DN, DSP-UP
  • Power requirements: 105-125VAC 60Hz (210-250VAC 50/60Hz) 120 watts maximum. Sleep mode 1 watts maximum
  • produkt dimensionen: 480 x 134 x 390 mm

CHF 17 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

CD6 SE

CD-Player

 

  • Frequency response: +0-3dB, 3Hz to 96kHz at rated output. 0.15dB 20Hz to 20kHz. (Balanced, 200k ohms load)@ 192kHz sample rate
  • Distortion: THD+N Less than .004% at 2V RMS BAL output
  • Signal-Noise-ratio: 110dB
  • Dynamic ranfe (AES17): 111dB
  • IMD (SMPTE): .003%
  • RMS Noise level: -95dBV (20-20kHz)
  • Gain: 16.5dB Balanced, 8.3dB SE.
  • Input impedance: Digital: 75 ohms RCA, 110 ohms AES/EBU, OPT 660nm TOSLink fiber 44.1 to 96kHz
  • Output impedance: 500 ohms Balanced, 250 ohms SE Main (2), 20K ohms minimum load and 2000pF maximum capacitance
  • Output Polarity: Non-inverting.
  • Max. Output: At 0.0dB input, 5V RMS into 200K ohm balanced load
  • Digital sample rates: 24 bits @ 44.1kHz to 192kHz, SPDIF, AES/EBU and USB 2.0 HS
  • Upsampling: Select Upsampling or Native mode; CD, RCA, AES/EBU, TOS upsample to 176.4 or 192kHz. USB upsamples to 88.2 or 96kHz
  • Master oscillator: 22.579mHz ±20Hz for 44.1, 88.2 & 176.4kHz. 24.576mHz ±20Hz for 48, 96 & 192kHz
  • Intrinsic jitter: <10ps
  • Outputs digital: XLR Balanced AES/EBU 110-ohms 4V P-P, BNC coax SPDIF 75-ohms 0.7V P-P
  • Channel separation: 103dB @ 1kHz
  • Push Buttons: Power, Previous, Stop, Pause, Play, Next, Input
  • Signal format (DISC): Sample freq. 44.1kHz, Quantization bit; 16bit linear/channel, Channel bit rate; 4.3218Mb/sec, Channel modulation code; EFM (8-14 modulation), Error correction;
  • Circ drive mechanism (top load): Wow & Flutter; Un-measureable (Quartz stability); Discs; Accepts 5" (12cm) and 3" (8cm) sizes
  • Optical pickup: Type; 3-beam LDGU (Laser Diode & Grating Unit), with holographic diffraction light pen, Laser; GaAlAs semiconductor, 780nm, 0.5mW Max. Output, Servo; Digitally-controlled low inertia linear positioning actuator
  • Jitter reduction: High-stability crystal-controlled re-clocking for all outputs
  • Display: Six-digit vacuum fluorescent with optical filter; LED Display; CD, AES, USB, RCA, TOS, Fast, Slow, Upsample, Power, 44.1, 48, 88.2, 96, 176.4, 192kHz
  • Remote buttons: Repeat track/disc, 0-9 digit entry keys, Scan ten seconds each track, Pause program, Stop program, Play, Shuffle tracks, Program enters selection on program list, Time elapsed, remaining track, remaining disc, A/B repeat segment, Filter select, Input select, Pause, Play, Skip>, Skip<, FF, FR, Upsample/Native mode, DSP-DN, DSP-UP
  • Power requirements: 105-125VAC 60Hz (210-250VAC 50/60Hz) 23 watts maximum. Sleep mode 0.5 watts maximum
  • NETTOGEWICHT: 11.80 kg

    produkt dimensionen: 480 x 134 x 311 mm

CHF 11 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

CD6

CD-Player

 

  • Frequency response: +0-3dB, 3Hz to 96kHz at rated output. 0.15dB 20Hz to 20kHz. (Balanced, 200k ohms load)@ 192kHz sample rate
  • Distortion: THD+N Less than .004% at 2V RMS BAL output
  • Signal-Noise-ratio: 110dB
  • Dynamic ranfe (AES17): 111dB
  • IMD (SMPTE): .003%
  • RMS Noise level: -95dBV (20-20kHz)
  • Gain: 16.5dB Balanced, 8.3dB SE.
  • Input impedance: Digital: 75 ohms RCA, 110 ohms AES/EBU, OPT 660nm TOSLink fiber 44.1 to 96kHz
  • Output impedance: 500 ohms Balanced, 250 ohms SE Main (2), 20K ohms minimum load and 2000pF maximum capacitance
  • Output Polarity: Non-inverting.
  • Max. Output: At 0.0dB input, 5V RMS into 200K ohm balanced load
  • Digital sample rates: 24 bits @ 44.1kHz to 192kHz, SPDIF, AES/EBU and USB 2.0 HS
  • Upsampling: Select Upsampling or Native mode; CD, RCA, AES/EBU, TOS upsample to 176.4 or 192kHz. USB upsamples to 88.2 or 96kHz
  • Master oscillator: 22.579mHz ±20Hz for 44.1, 88.2 & 176.4kHz. 24.576mHz ±20Hz for 48, 96 & 192kHz
  • Intrinsic jitter: <10ps
  • Outputs digital: XLR Balanced AES/EBU 110-ohms 4V P-P, BNC coax SPDIF 75-ohms 0.7V P-P
  • Channel separation: 103dB @ 1kHz
  • Push Buttons: Power, Previous, Stop, Pause, Play, Next, Input
  • Signal format (DISC): Sample freq. 44.1kHz, Quantization bit; 16bit linear/channel, Channel bit rate; 4.3218Mb/sec, Channel modulation code; EFM (8-14 modulation), Error correction;
  • Circ drive mechanism (top load): Wow & Flutter; Un-measureable (Quartz stability); Discs; Accepts 5" (12cm) and 3" (8cm) sizes
  • Optical pickup: Type; 3-beam LDGU (Laser Diode & Grating Unit), with holographic diffraction light pen, Laser; GaAlAs semiconductor, 780nm, 0.5mW Max. Output, Servo; Digitally-controlled low inertia linear positioning actuator
  • Jitter reduction: High-stability crystal-controlled re-clocking for all outputs
  • Display: Six-digit vacuum fluorescent with optical filter; LED Display; CD, AES, USB, RCA, TOS, Fast, Slow, Upsample, Power, 44.1, 48, 88.2, 96, 176.4, 192kHz
  • Remote buttons: Repeat track/disc, 0-9 digit entry keys, Scan ten seconds each track, Pause program, Stop program, Play, Shuffle tracks, Program enters selection on program list, Time elapsed, remaining track, remaining disc, A/B repeat segment, Filter select, Input select, Pause, Play, Skip>, Skip<, FF, FR, Upsample/Native mode, DSP-DN, DSP-UP
  • Power requirements: 105-125VAC 60Hz (210-250VAC 50/60Hz) 23 watts maximum. Sleep mode 0.5 watts maximum
  • NETTOGEWICHT: 11.80 kg

    produkt dimensionen: 480 x 134 x 311 mm

CHF 10 499.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1

DAC

DAC9

D/A-Wandler

 

Description available soon

 

NETTOGEWICHT: 6.30 kg

produkt dimensionen: 137 x 480 x 348 mm

CHF 9 999.00

  • verfügbar
  • 1 - 3 Tage Lieferzeit1